Indoor Cycling

Replacement straps for Sunlite FlatForm II pedals - Strap size: 340 x 55mm

Universal quick release skewer for placing your bike in the trainer or direct drive. This axle replaces the standard quick release, allowing racing bikes and mountain bikes to be used with Tacx trainers.

This narrow towel was developed specifically for indoor bike training sessions and is used by many professional riders during their warm-up or indoor training sessions. - Highly absorbent - Measures 30cm x 115cm

- Replacement belt - Select model based on model/roller size and belt size

The Saris Leveling Block keeps your bike level with your trainer. - Adds stability to your training ride. - For use with any rear wheel-mounted trainer. - Raises front bicycle tire 1.1 inches (2.8 cm) off the ground

Use these axle nuts to put a city or track bike in a Tacx trainer. The available axle nuts are M10x1 (T1415) and 3/8 Shimano Nexus (T1416). For use with Tacx classic trainers only

• Plastic riser block allows the position of front wheel at one of two heights

Keep corrosive sweat from reaching your frame while you're generating heat on your trainer. - Cell phone pouch included

CycleOps' Climbing Riser Block offers 3 levels of elevation to lift your front wheel and provide a workout simulating climbing hills. For steeper climbing workouts, 2 climbing blocks (sold separately) may be placed on top of each other for many different adjustment levels.

The Gel Block is an indispensable accessory for perfecting your position on the bike and provides a more natural feel to your training. - Reduces vibrations on the handlebars for more comfortable training - Non-slip Elastogel insert ensures maximum stability and alignment of the front wheel - Suitable for road and MTB

BLE USB Adapter gives Rouvy virtual training software the ability to seamlessly connect to Bluetooth devices and sensors. The adapter contains a Bluetooth (BLE) radio that allows PCs to communicate with BLE devices, including Saris smart indoor bicycle trainers and power meters. Most importantly, the BLE USB Adapter is necessary to update the firmware Over the Air (OTA) via VirtualTraining for the Hammer and Magnus bike trainers. - Bluetooth adapter for PCs to work with Rouvy - Needed for Over the Air Firmware Updates to Smart Indoor Bike Trainers. - Works with PC desktops and laptops.

Adjust resistance on Mag trainer without leaving the saddle. - Quick Release mounting system fits most stems. - For use with the Mag bike trainer only

- Includes clutch knob and L-bolt - Basic Trainer Clutch Knob is compatible with any Wind, Mag, Mag+, Magneto or Fluid trainer that already uses L-bolt - Magnus Clutch Knob should only be used with Magnus Smart Trainer - Watch our video to learn more

700x23c Trainer Tire is specifically designed for use on trainers for ultra quiet, smooth rolling durability.

The TPH-1 Tablet Grip from Minoura is the ultimate tablet holder for indoor training. Fitting a diameter between 28mm and 35mm, this stand will fit most bicycles. - Perfect accessory to use with LiveTraining Apps, The Sufferfest videos, or other media - SM clamp easily mounts or dismounts from the handlebar or tube - Spring-loaded clamp system is simple to use and securely holds your device in place - Holds from a 7.9 to 9.7 inch screen with 360 degree rotation system - Can mount to your repair stand so you can easily reference the Internet when working on your bike

This height-adjustable front wheel support can simulate both flat terrain and slopes perfectly - Unique design with 5 levels lets you adjust the height of your front wheel to simulate hill climbs up to 6% - Anti-slip rubber feet eliminate handlebar vibrations - Internal design that guarantees maximum wheel stability - Suitable for both road and MTB - You can attach to the trainer frame when not in use for easy transport and storage

• 35.5-inches x 79-inches • Black

The E-Thru Trainer Axle allows the use of a mountain bike in a Tacx trainer. These axles are only suitable for Tacx classic trainers.

Kurt Kinetic's 12mm Traxle Through-Axle lets you attach your mountain bike to a Kinetic trainer without changing the original skewer. The Kinetic Traxle comes in 3 thread pitches: - T-2101 Coarse: M12 x 1.75mm - T-2102 Medium: M12 x 1.5 - T-2100 Fine: M12 x 1.00mm (Fine XL has the same thread pitch and is a longer version of the fine Traxle)

The Saris thru axle adapter is designed for indoor use on Saris- or CycleOps-branded trainers only and should not be ridden outdoors. - Compatible with Classic series trainers and most Pro series trainers. Not compatible with PowerSync trainers. Contact us with trainer compatibility questions. - This adapter is designed to work with bikes that have a 142x12mm thru axle with 1.0 or 1.75 thread pitch. - The axle is threaded on both sides to fit both Syntace and Maxle/ABP style thru axle systems. - Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please reach out to your local bike shop or the bicycle manufacturer directly. What's Included - Thru axle - Washers - End caps with bolts

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

Our Trainer Axle is designed to adapt your Surly MDS/Gnot Boost thru-axle-equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - This axle is for Surly bikes with the MDS/Gnot Boost system. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum, and hard-anodized for rugged durability. - No special tools required. Design allows for wheel installation or removal using your standard 5 mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

With this Tacx wireless ANT+ receiver for Android devices with a micro USB port, you can connect to devices that communicate via ANT+. For example a heart rate meter, speed and cadence sensor, sports watch, GPS device or bike computer. This enables you to keep track of your performance continually. It also allows you to link an ANT+ trainer to the Tacx Cycling app (tablet) or Tacx Training app (smartphone), or connect an older model Tacx trainer which only has ANT+ to your telephone, so you can train with the Tacx Training app and Tacx Cloud. The device you want to connect must have a micro USB port and Android 4.3 or higher. This ANT+ dongle is only compatible with devices that have USB On-The-Go.

Adapts a thru axle hub bike for a Saris bike trainer. - Trainer Thru Axle Adapter For Saris Trainers - Thread pitch: 1.00 & 1.75 What's Included: - Thru axle - Washers - Endcaps with bolts Trainer Compatibility The Saris Trainer Thru Axle Adapter is designed for indoor use on Saris trainers only and should not be ridden outdoors. Compatible with current basic trainers. Not compatible with CycleOps PowerSync trainers. Contact us with trainer compatibility questions. Bike Compatibility Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please contact us.

The Saris thru axle adapter is designed for indoor use on Saris- and CycleOps-branded trainers only and should not be ridden outdoors. Compatible with current classic series trainers. Not compatible with the JetFluid Pro, SuperMagneto Pro, PowerBeam Pro, or PowerSync trainers. Contact us with trainer compatibility questions. - This adapter is designed to work with bikes that have a 142x12mm or 148x12mm thru axle with 1.0 or 1.75 thread pitch. - The axle is threaded on both sides to fit Syntace and Maxle/ABP style thru axle systems. - Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please reach out to your local bike shop or the bicycle manufacturer directly. - Adapts a thru axle hub bike for a trainer - Only compatible with current basic trainers - Fits most 142-148mm thru axle bikes with 1.0 or 1.75 thread pitch

This is the new small wheel adapter for use on newer Kinetic trainer models. A must for BMX, recumbents, and any bike with tires having an outside diameter of 22-inches or less. The small wheel adapter raises the level of the resistance unit of any of the Kinetic Trainers by up to three inches. In doing so, the trainer will fit tires with outside diameters as small as 16-inches. By using this adapter, Kinetic trainers accommodate most BMX, kids', and recumbent bikes. - Compatible with T-2xxx two-thousand series and T-6xxx six-thousand series trainers - Not compatible with 24-inch bicycles

The Saris 20/24-inch Wheel Adapter allows you to use your BMX or recumbent bike with your trainer.

Use these quick releases to put a racing bike with disc brakes or a mountain bike with a quick-release skewer in a Tacx direct drive trainer. Both axles are supplied with an adapter set so you can select the right combination for your bike. These axles are only suitable for the Tacx direct drives.

Use this ANT+ antenna to connect an ANT+ trainer to your computer. That enables you to use computer software during your training sessions, such as the Tacx Trainer software, Zwift, and TrainerRoad. These programs read the training data transmitted by an ANT+ trainer and can control the trainer. It features a long cable so the receiver can be placed close to the trainer for an optimal reception without loss. The antenna is compatible with all trainers that communicate wirelessly via ANT+.

- Remote control for CycleOps VirtualTraining to allow the rider to change the ride view, mark intervals, pause and virtually change gears when using with 400 series or Phantom 5 Indoor Cycle. - Compatible with tablet and mobile devices via Bluetooth Smart only (iPad 3 or newer, iPhone 4s or newer.) - Compatible with PC via ANT+ or Bluetooth Smart (Bluetooth Smart connection Windows 8 or ANT+ connection requires ANT+ dongle/antenna.)