- Non-SIS 5mm alloy ferrules - Sold individually - Color: Silver
- Alloy spacer converts an 8-speed rear hub to use a 7 speed cassette - Range: 4mm - Color: Silver
- Aheadset preload adjusting bolt
Sunlite's Cable End Button replaces the worn out piece that goes between your brake cable and the brake lever body. Replacing it along with cables and housing helps add new life to your brakes and shines u the bike, too!
Replacement bearing for the lower half of YST8003 #7 headset.
Replace the top bearing in your YST8300 headset with these caged ball bearings.
Interlok spacers nest into the lip of Cane Creek headset uppers for a rock solid, flex-free fit. - Composite construction
- Allows quick chain removal without tools - MissingLink 410HD|~|1sp|~|BMX Heavy Duty chain|~|9.4mm|~|each|~| - MissingLink 410|~|1sp|~|BMX|~|8.6mm|~|each|~| - MissingLink II|~|8sp|~|all|~|7.1mm|~|6/card|~| - MissingLink-9|~|9sp|~|all|~|6.6mm|~|6/card|~| - MissingLink-10R|~|10sp|~|KMC, Shimano, SRAM|~|5.9mm|~|6/card|~| - MissingLink-10CR|~|10sp|~|Campagnolo only|~|5.9mm|~|6/card|~| - MissingLink-11|~|11sp|~|Campy, KMC, Shimano|~|5.5mm|~|6/card|~|
- Longer B-screw needed when using 40t or 42t cog with most Shimano derailleurs
Shim spacers can be placed between bearing and compression cover in IS headsets to fine tune the fitment.
- 8x1mm Allen head
- Model: Replacement bolt - Compatibility: Allen, M5x16
KMC 3/16" Master Link Chain Links - For 3/16" chain, extra wide - Extra-wide, for non-derailleur bikes: BMX, cruisers, etc - Perfectly fits on KMC 415H & 415H-NP chains
$1.50 - $2.00
- Half-link connector allows you to add or subtract half of one link (1/2 inch) from the chain in order to optimize chain tension - Uses standard chain pin connector and tool
- Aluminum w/lock nut and mount - Slotted mount design
- Crank dust cap - Works with most three-piece crank models
- Routes cables underneath the bottom bracket - Will not rust or corrode
Stainless steel pedal washers - Sold in pairs
- Rubber - Color: Black
- Standard steel replacement
- Hoods with (FD) are Flight-Deck compatible
This is a replacement Brake Hose Cover for the Lever End of Shimano BH90-SBM, BH90-SB levers. - Covers brake hose fitting at the brake lever
- Replacement retaining clip for the Surly Tuggnut/Snuggnut
Finish off that great road bar tape job with Origin-8's Rubber End Plugs. These plugs come in a variety of colors to dress up your rig and fit most handlebars.
- Size: 1/2x1/8 & 3/32 (set) - Links: 1 each per bag
- M8 Top Plate Nut
• Compatible with most side pull and center pull brakes • All weather compound
Use to create your desired chain length in single-speed applications. Only one half link is needed. - Non-reusable - Width: 9.4 mm - Drivetrain Speeds: 1 - Color: Black - Chain Compatibility: Shimano , SRAM , Campagnolo , Connex , KMC
The Gyro G3 upper top plate is designed for use with the G3 detangler.
- For MTB levers - 7mm x 1mm - Aluminum construction
Page 1 of 130 Next page